Skip to main content

    Convert inches to Ri (Japanese Mile)

    East Asia · East Asian Length · historical · colonial

    Historically reconstructed The unit is no longer in use and its value is reconstructed from historical and scholarly sources — treat it as indicative.

    Quick answer

    1 inch = 0.000006468 Ri (Japanese Mile)

    1 inch = 0.000006468 Ri (Japanese Mile). Ri (Japanese Mile) is a traditional length unit from East Asia.

    Convert any amount

    inches =0.000006468 Ri (Japanese Mile)

    inches to Ri (Japanese Mile) table

    inchesRi (Japanese Mile)
    0.25 inches0.000001617 Ri (Japanese Mile)
    0.5 inches0.000003234 Ri (Japanese Mile)
    1 inch0.000006468 Ri (Japanese Mile)
    2 inches0.0000129361 Ri (Japanese Mile)
    3 inches0.0000194041 Ri (Japanese Mile)
    4 inches0.0000258722 Ri (Japanese Mile)
    5 inches0.0000323402 Ri (Japanese Mile)
    10 inches0.0000646804 Ri (Japanese Mile)
    20 inches0.000129361 Ri (Japanese Mile)
    25 inches0.000161701 Ri (Japanese Mile)
    50 inches0.000323402 Ri (Japanese Mile)
    100 inches0.000646804 Ri (Japanese Mile)

    About the Ri (Japanese Mile)

    Japanese mile ≈ 3.93 km.

    Symbol
    Value in SI
    1 Ri (Japanese Mile) = 3,927 metre
    Typical use
    navigation
    Source
    UnitConvertLab measurement atlas

    Every atlas conversion routes through the SI metre. See our methodology and data provenance pages for how these values are sourced and verified.

    Understanding the Ri (Japanese Mile)

    Written and last checked against the sources below on .

    The ri is the Japanese league — 3.927 kilometres, or thirty-six chō — and it is the unit the Edo-period highways were measured in. Every distance in a travel diary, a post-station record or an old milestone along the Tōkaidō is a ri figure.

    Thirty-six chō, and where that comes from

    The Japanese length system builds upward from the shaku: sixty shaku make a jō-scale step, and the chain continues through the chō of sixty ken, roughly 109 metres. Thirty-six chō make one ri. Because the shaku was fixed at 10/33 of a metre when Japan metricated, every unit above it acquired an exact metric value, and the ri became 3,927.27 metres — usually cited as 3.927 kilometres.

    The exactness is retrospective. Before the Meiji standardisation the ri, like the Chinese li it descends from, was a road measure with regional variation, and eastern and western Japan did not always agree. Edo-period figures should be read as good approximations of the modern value rather than as measurements against it.

    The highway unit

    The five great Edo highways were administered in ri. Post stations were spaced in ri, travel permits reckoned journeys in ri per day, and ichirizuka — earthen mounds planted with trees at one-ri intervals — marked the roads physically. Many ichirizuka survive along the Tōkaidō and Nakasendō, and they remain the most direct evidence of what the unit meant on the ground.

    A healthy traveller on foot covered roughly eight to ten ri in a day, which is thirty to forty kilometres, and that expectation shaped where stations were built. Reading an Edo itinerary in kilometres alone loses this: the ri count tells you how many days a journey took, and the metric distance does not.

    Sea ri and modern survivals

    The kairi, or sea ri, is the nautical mile of 1,852 metres — under half the land ri. Japanese maritime documents use it, and a bare "ri" in a shipping or naval context should be checked against the domain before conversion, exactly as with the Chinese li.

    On land the ri is no longer used for practical navigation, but it persists in place names, in the names of hiking trails that follow old highways, and in tourism signage that quotes both the historical ri distance and its metric equivalent. Conversion for those contexts is straightforward; the value is fixed and the audience expects both figures side by side.

    Converting an Edo itinerary

    An Edo travel record states distances between post stations in ri and fractions of a ri, and the sum of those stages is the length of the journey as it was administered rather than as a modern map measures it. Roads have been straightened, tunnelled and rerouted since, so a converted total will not match a present-day highway distance and should not be presented as if it should.

    The stronger approach is to convert stage by stage and compare each against the surviving route where it is known, noting where the modern road departs from the historical one. For the Tōkaidō and Nakasendō this is well documented, and the discrepancies are themselves informative: they show where terrain, not distance, governed the placement of stations.

    Distance markers along the old highways were placed at one-ri intervals, and many ichirizuka mounds survive. Where they do, they are the best available check on a converted itinerary, because they fix the historical measurement to a point on the ground rather than to a factor in a table.

    Common mistakes to avoid

    • The land ri is 3.927 km; the sea ri (kairi) is the nautical mile of 1.852 km — less than half.
    • Pre-Meiji ri varied regionally; Edo-period distances are approximations of the modern exact value.
    • A ri is not a Chinese li — the Japanese unit is nearly eight times longer.
    • Ichirizuka spacing reflects road routing and terrain, so surviving mounds validate the scale rather than a precise figure.

    Questions people ask about the Ri (Japanese Mile)

    How many kilometres is one Japanese ri?
    About 3.927 kilometres — thirty-six chō. The value became exact when the shaku was fixed at 10/33 of a metre during the Meiji metrication.
    Is the Japanese ri the same as the Chinese li?
    No, despite sharing a character and an origin. The Chinese li is 500 metres; the Japanese ri is 3,927 metres, roughly eight times longer.
    What are ichirizuka?
    Earthen mounds planted at one-ri intervals along the Edo-period highways to mark distance. Many survive along the Tōkaidō and Nakasendō and are the physical record of how the unit was used.

    Where the Ri (Japanese Mile) is used

    See how the Ri (Japanese Mile) sits alongside the other units in Japan.

    Sources for this section

    Frequently asked

    How many Ri (Japanese Mile) are in a inch?

    1 inch = 0.000006468 Ri (Japanese Mile). Multiply the number of inches by 0.000006468 to get Ri (Japanese Mile).

    What is Ri (Japanese Mile) used for?

    Japanese mile ≈ 3.93 km. It is classified as historical and dates from the colonial period.

    Is the Ri (Japanese Mile) value exact?

    Yes for practical purposes. UnitConvertLab converts every atlas unit through the SI metre, so the arithmetic itself introduces no rounding beyond the digits shown.

    How reliable is this Ri (Japanese Mile) conversion?

    Historically reconstructed — The unit is no longer in use and its value is reconstructed from historical and scholarly sources — treat it as indicative. Source: UnitConvertLab measurement atlas.

    How many kilometres is one Japanese ri?

    About 3.927 kilometres — thirty-six chō. The value became exact when the shaku was fixed at 10/33 of a metre during the Meiji metrication.

    Is the Japanese ri the same as the Chinese li?

    No, despite sharing a character and an origin. The Chinese li is 500 metres; the Japanese ri is 3,927 metres, roughly eight times longer.

    What are ichirizuka?

    Earthen mounds planted at one-ri intervals along the Edo-period highways to mark distance. Many survive along the Tōkaidō and Nakasendō and are the physical record of how the unit was used.

    What should I check before using a Ri (Japanese Mile) figure?

    The land ri is 3.927 km; the sea ri (kairi) is the nautical mile of 1.852 km — less than half. Pre-Meiji ri varied regionally; Edo-period distances are approximations of the modern exact value. A ri is not a Chinese li — the Japanese unit is nearly eight times longer. Ichirizuka spacing reflects road routing and terrain, so surviving mounds validate the scale rather than a precise figure.

    Cite this page

    UnitConvertLab. (2026). Convert inches to Ri (Japanese Mile). UnitConvertLab. Retrieved from https://unitconvertlab.com/regional/inch-to-ri-japan

    Report an incorrect value or source

    Regional units vary by district and by century. If this figure, its variant list or its citation is wrong where you are, tell us — the report carries the page context automatically.